PoE switches

24-port gigabit PoE switch with 2 uplinks and 2 SFP

Model TEG1128P-24-250W

Unmanaged rack-mount gigabit PoE switch with 24 PoE+ ports, two gigabit uplink ports and two SFP slots. Its PoE output is 230 W in total and 30 W per port.

PoE ports
24
Uplink ports
2
PoE budget
230 W
SFP
2 x SFP

Overview

Highlights

  • 24 x 10/100/1000 Mbps PoE+ ports (802.3af/at), 30 W per port
  • 230 W total PoE output
  • 2 x gigabit RJ45 uplinks and 2 x 1000Base-X SFP slots
  • Four modes: standard, priority, extend and VLAN
  • 1U 19-inch rack case, 56 Gbps switching capacity, 6 kV lightning protection
  • 8K MAC address table, 4 Mb buffer

At a glance

A 24-port gigabit PoE switch with 2 uplink ports, an SFP slot for fibre and a 230 W PoE budget, for powering and connecting IP cameras over Cat6.

PoE ports
24, Gigabit
Uplink
2 ports to the NVR or network
SFP
SFP
PoE budget
230 W
Cable
Cat6, up to 100 m per run to each camera Cat6 cable

PoE budget check

Cameras this switch can power at a typical draw per camera, using the 230 W budget and 24 PoE ports.

Power per camera Cameras Power used Limited by
4 W 24 96 W of 230 W Port count
6 W 24 144 W of 230 W Port count
8 W 24 192 W of 230 W Port count

Check each camera’s maximum power consumption in its datasheet; infrared at night and heaters raise it. Leave some headroom rather than loading the budget to the limit.

Check a budget for your own cameras

Specifications

Ports and standards

Network standards
IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3x, IEEE 802.3af, IEEE 802.3at
LED indicator
One Link/Act LED per portOne PoE MAX LED per portOne Power LED per device
Interfaces
24 x 10/100/1000 Base-T Ethernet ports (Data/Power)2 x 10/100/1000 Base-T Ethernet ports (Data)2 x 100/1000 Base-X SFP ports
Transmission media
Recommended: CAT5/5e UTP or better

Performance

Forwarding mode
Store-and-forward
Switch capacity
56 Gbps
Packet forwarding rate
41.7 Mpps
Buffer
4 Mb
MAC address table
8K

PoE

PoE budget
Total PoE output: 230 WSingle port: 15.4 W (802.3af), 30 W (802.3at)

Power

Power consumption
Below 250 W
Input voltage
100 to 240 V AC, 50/60 Hz

Physical and environment

Level of protection (port)
6 kV
Level of protection (power)
6 kV
Rack mounting
Supported
Desktop mounting
Supported
Wall mounting
Supported
Operating temperature
0 to 45 °C
Storage temperature
-40 to 70 °C
Operating humidity
10% to 90%, non-condensing
Storage humidity
5% to 90%, non-condensing
Certification
FCC, CE, RoHS

Features

Network modes
Standard: all ports communicate with each other, like an ordinary unmanaged PoE switchPriority: ports 1 to 8 are high-priority portsExtend: ports 17 to 24 reach up to 250 m and all ports communicate with each otherVLAN: ports 1 to 24 cannot communicate with each other but can communicate with ports 25, 26, SFP1 (27) and SFP2 (28)

Specifications are taken from the manufacturer's published information and may change. Confirm critical values with our sales desk before ordering.

Tenda product page

Works with

IP cameras

Cat6 cable

Support

Warranty and repairs

Warranty is as per Tenda’s terms for this model. For products bought from us, call our service team with the invoice number, the model and the product’s serial number.

From Tenda

Practical notes

  1. Add up the power draw of connected cameras and keep it within the PoE budget.
  2. Keep each Cat6 run within 100 m.
  3. Mount the switch where it can ventilate, ideally in a rack.

Request a quote

Share the quantity and delivery location for TEG1128P-24-250W. Our sales desk replies with price and availability, subject to stock.

You are a (optional)

Sending opens WhatsApp with your enquiry filled in, ready to send to our sales desk.

Similar models

Pairs with